Naren - Domestic Motor Controller

Model: DMC - CT

This product is a motor protection system with in-built motor starter that safeguards the Single Phase Monoblock and Openwell Submersible Motors against Overload and Dry Run. This product also has an OFF timer that can be adjusted by the user. This product has a built in cyclic timer that can be used to periodically turn ON and OFF the motor as per the desired time intervals. It also offers a feature of turning OFF of the motor when the overhead tank is full. DMC-CT allows the motor load to pass through the CT provided to sense the current . The current drawn by the motor is continuously monitored and displayed on the LCD. The low current and high current settings need to be adjusted by the user. The motor is turned OFF in case of over current, under current (dry run) and when any of the supply phases are absent thus protecting the motor from damages. The reason for the trip is displayed on the LCD. The sensors are provided additionally which when connected to the overhead tank, turns OFF the motor starter when the water fills up. The switch provided on the device can be used to turn ON/OFF the motor.
Features:
  • Cyclic Time
  • Overload Protection
  • Dry Run (Under Current) Protection
  • Tank Full OFF
  • Manual/Cyclic Mode
  • Motor OFF Timer
  • Elapsed time indication
  • Motor Cable Cut Protection
  • User Adjustable Overload and Dry Run Settings
  • Digital Ammeter
  • Digital Voltmeter
  • Error Display on LCD
  • Metal Body
  • Connector type design
  • Motor ON Indication
  • Easy Setup and Installation
Rating:
  • Upto 2HP
Maximum Current Range:
  • 30A
Connections:
    For Monoblock Pumps
  • Connect the incoming power supply lines 220V to connectors 1 and 2 respectively (load wires).
  • Connect the motor cables to connectors 3 and 4 respectively (load wires).
  • Connect the sensor wires to the connectors 5 and 6 (polarity does not matter)
    For Openwell Submersible Pumps
  • Connect the incoming power supply lines 220V to connectors 1 and 2 respectively (load wires).
  • Connect the motor cables to the motor starter
  • Connect 3 and 4 to the incoming of your motor starter (load wires)
  • Keep the MCB on the starter always in the ON position
  • Connect the sensor wires to the connectors 5 and 6 (polarity does not matter)
Operation:
    The LCD powers up automatically when the supply voltage is given. The device can be programmed into manual or cyclic mode. In manual mode, the motor can be turned ON by pressing the switch on the device. The same switch can be used to turn OFF the motor. In Cyclic mode, you can set the desired running and waiting times. The device switches ON and OFF the motor based on the set timings. While the motor is running, the device safeguards the motor against Overload and Dry Run besides the timing OFF. The sensors are provided as part of the package. If the sensors are connected and placed in the tank, the motor is also turned OFF as soon as the tank fills up.
Technical Specifications:
  • Wire Size to be used for Connectors 1,2,3 and 4 is a minimum of 1.5 sq. mm
  • The other wire sizes need to be minimum of 0.5 sq mm
Tripping time:
  • Overload - 12 seconds
  • Dry Run (Underload) - 8 seconds
  • Maximum OFF Time - 120 Minutes
  • Maximum ON time (Cyclic Mode) - 99 Hours
  • Maximum OFF timer (Cyclic Mode) - 99 Hours
Settings:
  • Turn the Overload [H( )] [green knob] to maximum (clockwise)
  • Turn the Dry Run [L( )] [Blue knob] to minimum (anticlockwise)
  • Turn ON the motor and observe the load current in the second line of the LCD
  • Set the Overload H( ) value to 2 points more than the load current by rotating and observing the change in H( ) value in the first line of the LCD.
  • Set the Dry Run L( ) value to 2 points less than the load current by rotating and observing the change in L( ) value in the first line of the LCD.
  • Motor OFF Timer is the first knob. If the timer is not required, turn it completely towards the left hand side.
  • If the OFF timer needs to be set, turn the white knob on the right hand side to increase the time which can be seen on the far right inside the brackets on the second line of the LCD
  • The numbers appearing next to the current reading outside the brackets are the time elapsed.
    Cyclic Timer Settings:
  • Press set key to enter the timer settings
  • Observe the cursor blinking in the ON time
  • Press increase key (on right hand side) to increase the timings (HH:MM:SS)
  • Press decrease key (on left hand side) to decrease the timings (HH:MM:SS)
  • After the ON time is set, press Set button
  • Observe the cursor blinking in the OFF time
  • Press increase key (on right hand side) to increase the timings (HH:MM:SS)
  • Press decrease key (on left hand side) to decrease the timings (HH:MM:SS)
  • Press Set again to save the timings and exit the settings
    Settings to select timer mode:
  • Power OFF the device
  • Press and hold the increase and decrease key together
  • Power ON the device
  • Release the key as soon as the setting mode prompts
  • Press increase key to select between Cut Off Mode / Cyclic mode
  • Press Set button again to save and exit the menu
  • Note: Set the L( ) value to minimum if the Dry Run Protection is not required.
Application:
    Naren DMC-1 is used in all Single Phase Monoblock and Openwell Submersible pumps as a protection mechanism to protect the motor against current and voltage irregularities. This device effectively switches OFF the motor in any irregularity and hence prevents burning of the motor windings. The reason for turning OFF is displayed on the LCD which makes the diagnosis easy. The motor safeguarding devices like these are very critical which will save the users from the costs incurred due to motor failures. This product also doubles as a water protection mechanism as the motor is automatically turned OFF as soon as the tank fills up.
Warranty:
    This product carries a warranty of 6 months from the date of purchase. Any issues within the warranty period will be attended to free of cost at our works in Bangalore. Post the warranty period, the product will be eligible for the paid service at our works. The invoice copy acts as a warranty card. The shipping of the product for repair will have to be done by the consumer.
    Product Helpline: +919972243774

  Watch Video (English)

  Watch Video (Kannada)

BUY NOW     Enquire on WhatsApp